Description
-
Protected by hydraulic overload
When the press is operating under overloading, the oil escapes through the metal seal and the press is brought to stop instantly.
-
Structural design
To avoid of the inevitable opening of C-type Press and reduce the deformation, furthermore, to extend the life of press, the rigid frame structure design is applied in SH2 series.
This structure would keep the parallel between slide & bolster, and better control the eccentric load to facilitate precise processing.
Specification
SH2-110 | ||||
---|---|---|---|---|
Model | 1 | 2 | ||
Capacity | ton | 110 | ||
Tonnage rating point (above B.D.C.) | mm | 5 | ||
Stroke length | mm | 110 | 180 | |
Stroke per minute | spm | 50~100 | 35~70 | |
Die height, slide to bolster | mm | 350 | 400 | |
Slide adjustment | mm | 90 | ||
Slide area (a1 x b1) | mm | 1360 x 520 | ||
Bolster area (a2 x b2) | mm | 1660 x 680 | ||
Bolster thickness | mm | 155 | ||
Side opening (b3 x h3) | mm | 700 x 285 | 700 x 335 | |
Approx dimensions | Bolster surface height h1 | mm | 900 | |
Press overall height h2 | mm | 3115 | 3200 | |
Position of anchor bolt (a3 x b4) | mm | 1950 x 1150 | ||
Floor space required (a4 x b5) | mm | 2240 x 1700 | ||
Max. measurement of press (a5 x b6) | mm | 2240 x 2460 | ||
Main motor | HP x p | 15 x 4 | ||
Required air pressure | kg/cm | 5 |
SH2-160 | ||||
---|---|---|---|---|
Model | 1 | 2 | ||
Capacity | ton | 160 | ||
Tonnage rating point (above B.D.C.) | mm | 6 | ||
Stroke length | mm | 130 | 200 | |
Stroke per minute | spm | 40~90 | 30~60 | |
Die height, slide to bolster | mm | 400 | 450 | |
Slide adjustment | mm | 100 | ||
Slide area (a1 x b1) | mm | 1500 x 580 | ||
Bolster area (a2 x b2) | mm | 1800 x 760 | ||
Bolster thickness | mm | 165 | ||
Side opening (b3 x h3) | mm | 780 x 325 | 780 x 375 | |
Approx dimensions | Bolster surface height h1 | mm | 900 | |
Press overall height h2 | mm | 3260 | 3345 | |
Position of anchor bolt (a3 x b4) | mm | 2270 x 1300 | ||
Floor space required (a4 x b5) | mm | 2530 x 1650 | ||
Max. measurement of press (a5 x b6) | mm | 2530 x 2368 | ||
Main motor | HP x p | 20 x 4 | ||
Required air pressure | kg/cm | 5 |
SH2-200 | ||||
---|---|---|---|---|
Model | 1 | 2 | ||
Capacity | ton | 200 | ||
Tonnage rating point (above B.D.C.) | mm | 7 | ||
Stroke length | mm | 150 | 250 | |
Stroke per minute | spm | 35~75 | 25~50 | |
Die height, slide to bolster | mm | 450 | 500 | |
Slide adjustment | mm | 110 | ||
Slide area (a1 x b1) | mm | 1850 x 650 | ||
Bolster area (a2 x b2) | mm | 2150 x 840 | ||
Bolster thickness | mm | 170 | ||
Side opening (b3 x h3) | mm | 860 x 365 | 860 x 415 | |
Approx dimensions | Bolster surface height h1 | mm | 1000 | |
Press overall height h2 | mm | 3700 | 3800 | |
Position of anchor bolt (a3 x b4) | mm | 2620 x 1400 | ||
Floor space required (a4 x b5) | mm | 2900 x 1750 | ||
Max. measurement of press (a5 x b6) | mm | 2900 x 2583 | ||
Main motor | HP x p | 30 x 4 | ||
Required air pressure | kg/cm | 5 |
SH2-250 | ||||
---|---|---|---|---|
Model | 1 | 2 | ||
Capacity | ton | 250 | ||
Tonnage rating point (above B.D.C.) | mm | 7 | ||
Stroke length | mm | 170 | 280 | |
Stroke per minute | spm | 25~60 | 20~40 | |
Die height, slide to bolster | mm | 450 | 550 | |
Slide adjustment | mm | 120 | ||
Slide area (a1 x b1) | mm | 2100 x 700 | ||
Bolster area (a2 x b2) | mm | 2400 x 920 | ||
Bolster thickness | mm | 180 | ||
Side opening (b3 x h3) | mm | 940 x 355 | 940 x 455 | |
Approx dimensions | Bolster surface height h1 | mm | 1100 | |
Press overall height h2 | mm | 4100 | 4255 | |
Position of anchor bolt (a3 x b4) | mm | 2920 x 1500 | ||
Floor space required (a4 x b5) | mm | 3200 x 1850 | ||
Max. measurement of press (a5 x b6) | mm | 3200 x 2703 | ||
Main motor | HP x p | 40 x 4 | ||
Required air pressure | kg/cm | 5 |
SH2-300 | ||||
---|---|---|---|---|
Model | 1 | 2 | ||
Capacity | ton | 300 | ||
Tonnage rating point (above B.D.C.) | mm | 6 | ||
Stroke length | mm | 200 | 300 | |
Stroke per minute | spm | 20~50 | 15~35 | |
Die height, slide to bolster | mm | 600 | 650 | |
Slide adjustment | mm | 130 | ||
Slide area (a1 x b1) | mm | 2400 x 900 | ||
Bolster area (a2 x b2) | mm | 2600 x 1200 | ||
Bolster thickness | mm | 200 | ||
Side opening (b3 x h3) | mm | 1220 x 530 | 1220 x 580 | |
Approx dimensions | Bolster surface height h1 | mm | 1150 | |
Press overall height h2 | mm | 4420 | 4520 | |
Position of anchor bolt (a3 x b4) | mm | 3260 x 1650 | ||
Floor space required (a4 x b5) | mm | 3560 x 2100 | ||
Max. measurement of press (a5 x b6) | mm | 3500 x 2978 | ||
Main motor | HP x p | 50 x 4 | ||
Required air pressure | kg/cm | 5 |